Get 5% off when you subscribe to our newsletter! CLICK HERE >
Installation Videos
Installation
Videos
Watch our instructional videos and learn
how to use Living in a Bubble products
Watch our instructional
videos and learn how to use
Living in a Bubble products
How To Install Our Side Door Magnetic Flyscreens
1. Remove your Living in a Bubble side door flyscreen from the zipper pouch bag. Hold it upright with the pleated end at the top.
2. Align the center of the flyscreen with the center of the van door. Beginning with the center, magnetically attach the top of the flyscreen to the top of your van’s door frame.
3. Continue attaching the flyscreen’s edge along the sides of the door frame.
4. Once the top and side magnets are attached to the door, straighten the flyscreen and attach the magnets at the bottom of the flyscreen.
Tip: Make sure to tuck the magnets around the rubber seals and be mindful of the door closure mechanism. When you are ready to leave and hit the road again, simply lift up the bottom of the flyscreen and tuck it out of the way. This will prevent it from getting caught in the track when you close the van door.
The extra magnets provided are to be used in any part of the vehicle that is not metal.
For more installation methods and pictures, click here.
2. Align the center of the flyscreen with the center of the van door. Beginning with the center, magnetically attach the top of the flyscreen to the top of your van’s door frame.
3. Continue attaching the flyscreen’s edge along the sides of the door frame.
4. Once the top and side magnets are attached to the door, straighten the flyscreen and attach the magnets at the bottom of the flyscreen.
Tip: Make sure to tuck the magnets around the rubber seals and be mindful of the door closure mechanism. When you are ready to leave and hit the road again, simply lift up the bottom of the flyscreen and tuck it out of the way. This will prevent it from getting caught in the track when you close the van door.
The extra magnets provided are to be used in any part of the vehicle that is not metal.
For more installation methods and pictures, click here.
How To Install Our Rear Door Magnetic Flyscreens
1. Remove your Living in a Bubble rear door flyscreen from the zipper pouch bag. Hold it upright with the pleated end at the top.
2. Align the center of the flyscreen with the center of the van door. Beginning with the center, magnetically attach the top of the flyscreen to the top of your van’s door frame.
3. Continue attaching the flyscreen’s edge along the sides of the door frame.
4. Once the top and side magnets are attached to the door, straighten the flyscreen and attach the magnets at the bottom of the flyscreen.
Tip: Make sure to tuck the magnets around the rubber seals and be mindful of the door closure mechanism. When you are ready to leave and hit the road again, simply lift up the bottom of the flyscreen and tuck it out of the way. This will prevent it from getting caught in the track when you close the van door.
The extra magnets provided are to be used in any part of the vehicle that is not metal.
For more installation methods and pictures, click here.
2. Align the center of the flyscreen with the center of the van door. Beginning with the center, magnetically attach the top of the flyscreen to the top of your van’s door frame.
3. Continue attaching the flyscreen’s edge along the sides of the door frame.
4. Once the top and side magnets are attached to the door, straighten the flyscreen and attach the magnets at the bottom of the flyscreen.
Tip: Make sure to tuck the magnets around the rubber seals and be mindful of the door closure mechanism. When you are ready to leave and hit the road again, simply lift up the bottom of the flyscreen and tuck it out of the way. This will prevent it from getting caught in the track when you close the van door.
The extra magnets provided are to be used in any part of the vehicle that is not metal.
For more installation methods and pictures, click here.
How To Install Our Front Window Flyscreens
1. Open your car’s front door.
2. Slip the Living in a Bubble front window flyscreen over the top of the window frame.
3. Pull the flyscreen down and attach the magnetic strip to the car door.
4. Fasten and tighten the velcro around the base of the mirror mount.
5. Take the two loose ends and place them inside the door towards the interior side of the van.
6. Attach and tighten the loose ends with the buckle and toggle fasteners on the interior side of the van to create a tight fit.
2. Slip the Living in a Bubble front window flyscreen over the top of the window frame.
3. Pull the flyscreen down and attach the magnetic strip to the car door.
4. Fasten and tighten the velcro around the base of the mirror mount.
5. Take the two loose ends and place them inside the door towards the interior side of the van.
6. Attach and tighten the loose ends with the buckle and toggle fasteners on the interior side of the van to create a tight fit.
How To Install Our Insulated Black Out Window Covers For Driver And Passenger Windows (Mercedes Sprinter)
1. Remove your Living in a Bubble window cover from the packaging.
2. With the black side against the glass, place the cover on the window (passenger and driver door windows). The magnets will easily latch to the metal sides of the window frame.
3. Finally, ensure all edges are securely aligned on the window.
2. With the black side against the glass, place the cover on the window (passenger and driver door windows). The magnets will easily latch to the metal sides of the window frame.
3. Finally, ensure all edges are securely aligned on the window.
How To Install Our Insulated Black Out Window Covers For Rear Windows
1. Remove your Living in a Bubble window cover from the packaging.
2. With the black side against the glass, place the cover on the back door window (left and right sides). The magnets will easily latch to the metal sides of the window frame.
3. Finally, ensure all edges are securely aligned on the window.
2. With the black side against the glass, place the cover on the back door window (left and right sides). The magnets will easily latch to the metal sides of the window frame.
3. Finally, ensure all edges are securely aligned on the window.
How To Install Our Insulated Black Out Windshield Cover
1. With the black fabric facing up, fully open your Living in a Bubble windshield and place it on the dash of your van.
2. Where the window glass and dash meet, push the bottom of the windshield in to create a seal at the bottom of the window. Ensure that the blackout cover is seated correctly across the entire length of the window.
3. Vans with rear view mirror: Wrap it around the rear view mirror, one side at a time. Use the magnets in the centre to seal around the mirror and adjust the drawstrings to fast tightly.
4. Vans with technology box: Using the provided hooks that go under the headliner, hook on the window cover with the pull cord locks on either side to pull the cover close to the glass. Seal the centre with the magnets and adjust the drawstrings to fast tightly.
5. Pull down the sun visors to hold it in place.
2. Where the window glass and dash meet, push the bottom of the windshield in to create a seal at the bottom of the window. Ensure that the blackout cover is seated correctly across the entire length of the window.
3. Vans with rear view mirror: Wrap it around the rear view mirror, one side at a time. Use the magnets in the centre to seal around the mirror and adjust the drawstrings to fast tightly.
4. Vans with technology box: Using the provided hooks that go under the headliner, hook on the window cover with the pull cord locks on either side to pull the cover close to the glass. Seal the centre with the magnets and adjust the drawstrings to fast tightly.
5. Pull down the sun visors to hold it in place.
How To Install Our Insulated Black Out Roof Fan Vent Cover
1. Unscrew the vent fan flange from the inside of the van.
2. With the black side facing down, place the Living in a Bubble fan cover on any flat surface (ex: table, countertop, etc.)
3. Place the vent fan flange on top of the Living in a Bubble fan cover. Make sure the sides are aligned with each other.
4. Place the provided magnets along the plastic flange. They will snap in alignment with the magnets sewn in the Living in a Bubble fan cover.
5. Use tape to secure the loose magnets on the vent fan flange. This will prevent them from moving around or shifting positions.
6. Re-install the vent flange back to the ceiling of your van.
2. With the black side facing down, place the Living in a Bubble fan cover on any flat surface (ex: table, countertop, etc.)
3. Place the vent fan flange on top of the Living in a Bubble fan cover. Make sure the sides are aligned with each other.
4. Place the provided magnets along the plastic flange. They will snap in alignment with the magnets sewn in the Living in a Bubble fan cover.
5. Use tape to secure the loose magnets on the vent fan flange. This will prevent them from moving around or shifting positions.
6. Re-install the vent flange back to the ceiling of your van.
How To Install Our Insulated Black Out Window Covers For Driver And Passenger Windows (RAM Promaster / Fiat Ducato)
1. Remove your Living in a Bubble window cover from the packaging.
2. With the black side against the glass, place the cover on the window (passenger and driver side windows). The magnets will easily latch to the metal sides of the window frame.
3. With the metal tabs provided, remove the film from the back and adhere to the plastic trim matching with the magnets location.
4. Stick the provided magnets along the plastic frame. This will prevent them from moving around or shifting positions. They will snap in alignment with the magnets sewn in the Living in a Bubble window cover.
5. Finally, ensure all edges are securely aligned on the window.
2. With the black side against the glass, place the cover on the window (passenger and driver side windows). The magnets will easily latch to the metal sides of the window frame.
3. With the metal tabs provided, remove the film from the back and adhere to the plastic trim matching with the magnets location.
4. Stick the provided magnets along the plastic frame. This will prevent them from moving around or shifting positions. They will snap in alignment with the magnets sewn in the Living in a Bubble window cover.
5. Finally, ensure all edges are securely aligned on the window.
X
Where are you?
X
Where are you?
We Care About Your Privacy
We and our partners store and/or access information on a device, such as unique IDs in cookies to process personal data. You may accept or manage your choices by clicking below, including your right to object where legitimate interest is used, or at any time in the privacy policy page. These choices will be signaled to our partners and will not affect browsing data.
We and our partners process data to provide:
- Use precise geolocation data.
- Actively scan device characteristics for identification.
- Store and/or access information on a device.
- Personalised ads and content, ad and content measurement, audience insights and product development.
Privacy Policy
We and our partners store and/or access information on a device, such as unique IDs in cookies to process personal data. You may accept or manage your choices by clicking below, including your right to object where legitimate interest is used, or at any time in the privacy policy page. These choices will be signaled to our partners and will not affect browsing data.
We and our partners process data to provide:
- Use precise geolocation data.
- Actively scan device characteristics for identification.
- Store and/or access information on a device.
- Personalised ads and content, ad and content measurement, audience insights and product development.